Do you want to install a gas-powered wall heater? Check to see if the line from the previous heater is still in use. If not, put in the new gas line with a tee, sediment trap and manual gas shut-off valve in the same place as the old one.
Vermiculite may contain asbestos. Call a licensed pro.
Ventilation
Ventilation is the method by which 'clean' air (normally outdoors air) is made available to an area, and then old air is taken out. It is done through mechanical or natural means. Ventilation is essential to ensure the quality of indoor air by providing oxygen and metabolism decreasing metabolic pollutants, such as CO2 and odour and aiding in reducing contaminants from the use of combustion equipment. The importance of ventilation is improving the comfort of occupants, as well as to cut down on energy use by the reduction of temperatures.
If you're putting in a gas water heater, ensure your water and gas lines are completely cut off prior to beginning work. It will avoid any accident or explosions that might occur when working with the lines. If you are setting up an electrical model shut off the electrical power source as well.
Make sure you have all the required tools and materials. You'll also need pliers, a pipe wrench and hacksaw. It is important to get all the necessary equipment, including a test of voltage or electrical safety devices.
Install a temperature relief and pressure valve if needed. Be sure it's certified the same as your new water heater. When you screw the valve in position, tightly wrap the threads gas heater installers with Teflon (three times) and then attach the discharge pipe made of copper. The pipe is to be laid down from the large, circular opening on the tank. It's about 7-6 in. (10.2-10 cm) above ground level.
Thermostat
A thermostat is an important element of the heater installation. It senses temperature within a space and turns up or down your heater in order to regulate the temperature. It's also used in combination with other components to generate and disperse conditioned air across your house.
There is a range of thermostats, based on what you want and what your budget. Thermostats are available in both electronic and mechanical options. Modern models have bright screens and simple interfaces, replacing the classic dial-style thermostat. Many of these thermostats can be more adaptable than traditional mechanical models and many allow you to alter temperatures during the day.
They typically use sensors that measure temperature. However, there are some that use a microcontroller to read the thermistor's resistance element to determine its temperature. Digital thermostats are more accurate in comparison to other forms of thermostat. They also can be programmed which means you are able to set the time when they turn on and off at certain times of the day.
Many homeowners still prefer mechanical thermostats because of their cost and convenience. Bimetallic strips consist from a laminate of two metals. As the strip gets heated, one of the metals expands more than the others and bends slightly. The heater is then switched to on in the system. When the strip cools down it expands and snaps back in place. The flow of electricity is altered and the heater shuts down.
Thermostats must be set in a central area that is far from windows, doors and heater vents in order to guarantee a reliable reading. It is the ideal way to ensure an even temperature across the entire house. The thermostat can then control the heating and cooling systems efficiently.
Electrical
The wiring of electrical wires in a heater installation can be tricky. You should let professionals handle the wiring for you if do not feel comfortable. A competent electrician can make sure the dimensions of the circuit used by heaters are in accordance with the capacity of the heater and that all connections are safe and secure.
Before you do any work on the electric wiring, turn off the power to the heater. This could be done by turning off the gas breaker to your heater for water or switching off the circuit breaker in your home. After that, you should remove the water from all pipes, including cold and hot water tanks. Stop the drain valves.
Installation of a heater that operates on 240 volts will require an entire circuit connected to the heater. This will consist of three wires, two black 240 volt supply wires and an earth wire. The wires would be routed from the circuit breaker, through the junction box before going on to the heater.
It is essential to never get in touch with or touch live wires. It is possible to receive an electric shock or, even more dangerously, a fatal one. Use A voltage tester in order to verify whether the circuit you're near to touching is live.
The voltmeter is a tool for checking the voltage levels in the system you have. If the voltmeter says that there is no current between the leads of the electrical wires, and the lug screws that they are connected to It is a safe way to go ahead. It is recommended to consult an electrician when the voltmeter displays that voltages are present.
Make sure that the circuit breaker or fuse has been labeled in order that it will not be accidentally turned off. Also, you can put a tag, lock or key on the circuit breaker or fuse to protect it from being misused by kids or persons who don't know the purpose behind it. In the event of a failure to secure it, it could lead to serious injury or death, aswell in voiding any warranties.
A special electric heating cable prefers to be used over standard 12-2-2 NM electrical cable, or BX armoured cable. The wire is made with different conductors that of normal wires. It's specifically designed to handle the higher voltage of baseboard heating systems. If you don't utilize this type of wire, it's likely that the heat generated by the electric heater could create a situation where these traditional wires become hot and ignite or melt. This could result in a explosion and potentially cause injuries or kill you.